Open Access. Powered by Scholars. Published by Universities.®

Mining Engineering Commons

Open Access. Powered by Scholars. Published by Universities.®

1,195 Full-Text Articles 1,520 Authors 205,098 Downloads 38 Institutions

All Articles in Mining Engineering

Faceted Search

1,195 full-text articles. Page 6 of 16.

Recovery Of Phosphate Minerals From Plant Tailings Using Direct Froth Flotation Process, Ashraf Alsafasfeh 2017 Missouri University of Science and Technology

Recovery Of Phosphate Minerals From Plant Tailings Using Direct Froth Flotation Process, Ashraf Alsafasfeh

Masters Theses

"The wastes produced from phosphate industry presents many challenges due to the economic and environmental impacts of their disposal. In the meantime, scarcity of high-grade phosphate ores persuades researchers to find novel methods of upgrading these wastes (secondary sources) and recycling them in the production plant circuit. The goal of this study is to investigate the potential to upgrade the phosphorus content in the tailing produced from a phosphorous production plant using direct froth flotation process. Characterization studies such as X-ray diffraction (XRD), scanning electron microscopy (SEM), and mineral liberation analysis (MLA) were first conducted to identify the mineralogical and ...


Calculation Of The Edge Effect Offset For High Extraction Coal Panels, Joshua Hescock 2017 University of Kentucky

Calculation Of The Edge Effect Offset For High Extraction Coal Panels, Joshua Hescock

Theses and Dissertations--Mining Engineering

The Surface Deformation Prediction System (SDPS) program has been developed as an engineering tool for the prediction of subsidence deformation indices through the implementation of an influence function. SDPS provides reliable predictions of mining induced surface displacements, strains, and tilt for varying surface topography. One of the key aspects in obtaining reliable ground deformation prediction is the determination of the edge effect offset. The value assigned to the edge effect corresponds to a virtual offsetting of boundary lines delineating the extracted panel to allow for roof cantilevering over the mined out area.

The objective of this thesis is to describe ...


Modelling Transport And Deposition Of Coarse Particles In Viscoplastic Tailings Beach Flows, John Matthew Treinen 2017 University of Colorado at Boulder

Modelling Transport And Deposition Of Coarse Particles In Viscoplastic Tailings Beach Flows, John Matthew Treinen

Civil Engineering Graduate Theses & Dissertations

The flow of thickened mine tailings within a tailings storage facility is a complex interaction between unconstrained viscoplastic free surface flow and possible coarse particle settling within the flow depth. The broad focus of this work is developing a robust framework for modelling tailings beach flows. Modelling tailings flow evolution in three dimensions within a storage facility will ultimately provide greater understanding of beach slope formation, as well as the ability to optimize deposition sequencing.

This thesis focuses on the first step of developing a tailings model considering the transport and settling of mono-sized coarse particles within two dimensional (length ...


Modelling Transport And Deposition Of Coarse Particles In Viscoplastic Tailings Beach Flows, John Matthew Treinen 2017 University of Colorado at Boulder

Modelling Transport And Deposition Of Coarse Particles In Viscoplastic Tailings Beach Flows, John Matthew Treinen

Civil Engineering Graduate Theses & Dissertations

The flow of thickened mine tailings within a tailings storage facility is a complex interaction between unconstrained viscoplastic free surface flow and possible coarse particle settling within the flow depth. The broad focus of this work is developing a robust framework for modelling tailings beach flows. Modelling tailings flow evolution in three dimensions within a storage facility will ultimately provide greater understanding of beach slope formation, as well as the ability to optimize deposition sequencing.

This thesis focuses on the first step of developing a tailings model considering the transport and settling of mono-sized coarse particles within two dimensional (length ...


Laboratory Performance Comparison Of Vortecone Inertial Dust Scrubber To Flooded-Bed Dust Scrubber, Adam J. Levy 2017 University of Kentucky

Laboratory Performance Comparison Of Vortecone Inertial Dust Scrubber To Flooded-Bed Dust Scrubber, Adam J. Levy

Theses and Dissertations--Mining Engineering

Increasing incidence of Black Lung disease in miners since the early 1990s has concerned law makers and the mining industry. New regulations promulgated by MSHA in 2014 lowered the permissible limit of dust exposure of underground workers. The hazards of respirable coal dust have been common knowledge throughout the mining industry since the enactment of the 1969 Federal Coal Mine Health and Safety Act, and many administrative controls have been put in place since its enactment.

The purpose of this thesis is to analyze the performance of a Vortecone scrubber, used in the automotive industry to remove paint overspray from ...


Surface Chemisty Study Of Monazite Flotation In Coal Refuse Systems, Wencai Zhang 2017 University of Kentucky

Surface Chemisty Study Of Monazite Flotation In Coal Refuse Systems, Wencai Zhang

Theses and Dissertations--Mining Engineering

Rare earth mineral recovery from alternative resources such as coal and coal byproducts is increasingly important to provide an opportunity for economic recovery from U.S. sources. Currently, China produces the majority of the 149,000 tons of rare earth elements used annually worldwide of which the U.S. imports 11% or around 16,000 tons. There are no significant mining operations producing rare earth elements in the U.S. However, there are many U.S. sources containing rare earth minerals such as monazite including heavy mineral sand and phosphate operations. Monazite mineral particles of a few microns have also ...


Assessment Of Potential Impacts To Subsurface Bodies Of Water Due To Underground Coal Mining, Gabriel Bode-Jimenez 2017 University of Kentucky

Assessment Of Potential Impacts To Subsurface Bodies Of Water Due To Underground Coal Mining, Gabriel Bode-Jimenez

Theses and Dissertations--Mining Engineering

Underground coal mining operations induce ground movements, which may impact overlying hydrogeologic systems. Potential impacts mainly include changes in the hydraulic conductivity of overlying strata, decreasing of the hydraulic head and changes in water flow. The present research quantifies potential hydrogeologic impacts caused by underground mining through modeling of pre- and post-mining hydrogeologic systems.

Three-dimensional conceptual hydrogeologic models were constructed with the Processing Modflow for Windows software package (PMWiN). The models are based on an actual case study, but were simplified in terms of geometry and material properties. Water flow was simulated under changing hydrogeologic properties. A number of scenarios ...


Assessment Of Potential Impacts To Surface And Subsurface Water Bodies Due To Longwall Mining, Christopher R. Newman, Zacharias Agioutantis, Gabriel Boede Jimenez Leon 2017 University of Kentucky

Assessment Of Potential Impacts To Surface And Subsurface Water Bodies Due To Longwall Mining, Christopher R. Newman, Zacharias Agioutantis, Gabriel Boede Jimenez Leon

Mining Engineering Faculty Publications

Ground movements due to longwall mining operations have the potential to damage the hydrological balance within as well as outside the mine permit area in the form of increased surface ponding and changes to hydrogeological properties. Recently, the Office of Surface Mining, Reclamation and Enforcement (OSMRE) in the USA, has completed a public comment period on a newly proposed rule for the protection of streams and groundwater from adverse impacts of surface and underground mining operations (80 FR 44435). With increased community and regulatory focus on mining operations and their potential to adversely affect streams and groundwater, now there is ...


Modeling Dynamic Community Acceptance Of Mining Using Agent-Based Modeling, Mark Kofi Boateng 2017 Missouri University of Science and Technology

Modeling Dynamic Community Acceptance Of Mining Using Agent-Based Modeling, Mark Kofi Boateng

Doctoral Dissertations

"This research attempts to provide fundamental understanding into the relationship between perceived sustainability of mineral projects and community acceptance. The main objective is to apply agent-based modeling (ABM) and discrete choice modeling to understand changes in community acceptance over time due to changes in community demographics and perceptions. This objective focuses on: 1) formulating agent utility functions for ABM, based on discrete choice theory; 2) applying ABM to account for the effect of information diffusion on community acceptance; and 3) explaining the relationship between initial conditions, topology, and rate of interactions, on one hand, and community acceptance on the other ...


Pillar Design For St. Peter Sandstone Formation, Francis Anohomah Arthur 2017 Missouri University of Science and Technology

Pillar Design For St. Peter Sandstone Formation, Francis Anohomah Arthur

Doctoral Dissertations

"Silica sands produced primarily from St. Peter Sandstone are used for hydraulic fracturing in the petroleum industry, glassmaking, chemicals, ceramics, filtration and the foundry industry in the US. The recent high demand for silica sands for hydraulic fracturing has triggered increased production and commissioning of new silica sand mines to support natural gas production from shale and tight gas deposits in the US. Most mines use surface mining methods to extract St. Peter Sandstone. The room and pillar mining method has been successfully used for St. Peter Sandstone mining in a few US locations, however, no one has proposed a ...


Real-Time Diesel Particulate Matter Monitoring In Underground Mine Atmospheres, Association With The Standard Method And Related Challenges, Muhammad Usman Khan 2017 Missouri University of Science and Technology

Real-Time Diesel Particulate Matter Monitoring In Underground Mine Atmospheres, Association With The Standard Method And Related Challenges, Muhammad Usman Khan

Doctoral Dissertations

"Diesel-powered equipment is a significant component of underground mining operations. Miners' exposure to diesel exhaust is harmful. The standard Diesel Particulate Matter (DPM) monitoring method (NIOSH 5040 method) has limitations that preclude rapid DPM estimation and detailed understanding of DPM variations over time. However, real-time DPM monitors do not inherit these limitations. Biodiesel is often used as a substitute for regular petroleum-diesel because of its ability to emit less DPM. However, accuracy of available real-time DPM monitors has not been determined in mines using 70% to 99% (high-percent) biodiesel. The present research addresses this need by rigorous testing of a ...


Lhd Vibrations Analysis And Numerical Modeling During Operations, Kgosietsile Kolobe 2017 Missouri University of Science and Technology

Lhd Vibrations Analysis And Numerical Modeling During Operations, Kgosietsile Kolobe

Doctoral Dissertations

"Load-haul-dump vehicles (LHDs) are extensively used as primary loaders in mining operations. LHDs have proven to be vigorous, extremely productive and reliable in mining applications. They have a wide range of tramming capacities that have enabled them to become an essential component in the hard rock mining industry.

Increased mining economic challenges and global competition means the mining industry has to maximize productivity by cutting down operating and capital costs. Also, improvements in safety standards have led to the demand for safer and efficient machines.

LHD operators are at a high risk of whole-body vibrations (WBVs) exposure leading to musculoskeletal ...


The Andacollo's Mining Community: Ethnographic Work-Based Approach To Corporate Social Responsibility Policies And Practices, Ubirata de Oliveira 2017 Walden University

The Andacollo's Mining Community: Ethnographic Work-Based Approach To Corporate Social Responsibility Policies And Practices, Ubirata De Oliveira

Walden Dissertations and Doctoral Studies

This ethnographic study was designed to explore the phenomenon of corporate social responsibility (CSR) in the mining industry. The research addressed the impacts of a problematic, systemic, and ethnocentric (top-down) CSR approach driven by a transnational mining company, and proposed a novel cultural relativist (bottom-up) CSR approach looking at the social needs of the community. Solving the problem stemming from the ethnocentric approach is important for both the mining company and the community affected by the CSR program, as it will alter dynamics between actors and mitigate social conflicts. The purpose of this study was to investigate factors that improve ...


Fiber Bragg Grating Sensors For Mainstream Industrial Processes, Gary Allwood, Graham Wild, Steven Hinkley 2017 Edith Cowan University

Fiber Bragg Grating Sensors For Mainstream Industrial Processes, Gary Allwood, Graham Wild, Steven Hinkley

ECU Publications Post 2013

This paper reviews fiber Bragg grating sensing technology with respect to its use in mainstream industrial process applications. A review of the various types of sensors that have been developed for industries such as power generation, water treatment and services, mining, and the oil and gas sector has been performed. A market overview is reported as well as a discussion of some of the factors limiting their penetration into these markets. Furthermore, the author’s make recommendations for future work that would potentially provide significant opportunity for the advancement of fiber Bragg grating sensor networks in these mainstream industries.


Controlling Properties Of Agglomerates For Chemical Processes, Joseph A. Halt 2017 Michigan Technological University

Controlling Properties Of Agglomerates For Chemical Processes, Joseph A. Halt

Dissertations, Master's Theses and Master's Reports

Iron ore pellets are hard spheres made from powdered ore and binders. Pellets are used to make iron, mainly in blast furnaces. Around the time that the pelletizing process was developed, starch was proposed as a binder because it’s viscous, adheres well to iron oxides, does not contaminate pellets and is relatively cheap. In practice, however, starch leads to weak pellets with rough surfaces – these increase the amount of dust generated within process equipment and during pellet shipping and handling. Thus, even though the usual binder (bentonite clay) contaminates pellets, pelletizers prefer it to starch or other organics.

This ...


Electromagnetic Signal Feedback Control For Proximity Detection Systems, Adam K. Smith 2017 Michigan Technological University

Electromagnetic Signal Feedback Control For Proximity Detection Systems, Adam K. Smith

Dissertations, Master's Theses and Master's Reports

Coal is the most abundant fossil fuel in the United States and remains an essential source of energy. While more than half of coal production comes from surface mining, nearly twice as many workers are employed by underground operations.

One of the key pieces of equipment used in underground coal mining is the continuous mining machine. These large and powerful machines are operated in confined spaces by remote control. Since 1984, 40 mine workers in the U. S. have been killed when struck or pinned by a continuous mining machine. It is estimated that a majority of these accidents could ...


A Novel Method For Sensorless Speed Detection Of Brushed Dc Motors, Ernesto Vazquez-Sanchez, Joseph Sottile, Jaime Gomez-Gil 2016 University of Valladolid, Spain

A Novel Method For Sensorless Speed Detection Of Brushed Dc Motors, Ernesto Vazquez-Sanchez, Joseph Sottile, Jaime Gomez-Gil

Mining Engineering Faculty Publications

Many motor applications require accurate speed measurement. For brushed dc motors, speed can be measured with conventional observers or sensorless observers. Sensorless observers have the advantage of not requiring any external devices to be attached to the motor. Instead, voltage and/or current are measured and used to estimate the speed. The sensorless observers are usually divided into two groups: those based on the dynamic model, and those based on the ripple component. This paper proposes a method that measures the current of brushed dc motors and analyses the position of its spectral components. From these spectral components, the method ...


Ignimbrites To Batholiths, Chad Deering 2016 Michigan Technological University

Ignimbrites To Batholiths, Chad Deering

TechTalks

Ignimbrites sample large magma reservoirs in the Earth’s upper crust, sometimes digging deep enough to link the volcanic realm with the plutonic world. Integrating textural, petrological, geochemical, and geochronological information on such deposits with geophysical signals suggest incremental growth and evolution of subvolcanic magma bodies that are dominated by high crystallinity mush zones, but sometimes remain sufficiently liquid to erupt. The eruptible upper portions are either extracted melt from the mush and constitute only a small volumetric fraction of the vertically extensive mushy batholithic magma body. The high-flux, ignimbrite flare-up phases are typically preceded by waxing magmatism that prime ...


Explosion Testing Of A Polycarbonate Safe Haven Wall, Kyle A. Perry, Rex A. Meyr 2016 Missouri University of Science and Technology

Explosion Testing Of A Polycarbonate Safe Haven Wall, Kyle A. Perry, Rex A. Meyr

Mining and Nuclear Engineering Faculty Research & Creative Works

The MINER Act of 2006 was enacted by MSHA following the major mining accidents and required every underground coal mine to install refuge areas to help prevent future fatalities of trapped miners in the event of a disaster where the miners cannot escape. A polycarbonate safe haven wall for use in underground coal mines as component of a complete system was designed and modeled using finite element modeling in ANSYS Explicit Dynamics to withstand the MSHA required 15 psi (103.4 kPa) blast loading spanning 200 milliseconds. The successful design was constructed at a uniform height in both half-width scale ...


Haul Truck Tires Recycling, Omkar Bhave 2016 University of Arkansas, Fayetteville

Haul Truck Tires Recycling, Omkar Bhave

Chemical Engineering Undergraduate Honors Theses

The disposal of large Off-the-Road (OTR) tires is an increasingly important concern. These tires can weigh up to 8,450 pounds with an overall diameter and width of approximately 140.7 inches and 45.1 inches respectively. OTR tires are used for mining vehicles such as haul trucks, wheel loaders, backhoes, graders, and trenchers.[1] These new tires cost between $38,000 and $50,000 each, depending on multiple factors including oil prices and the cyclical nature of the industry. Haul trucks contain six tires per vehicle, and mines replace these tires around every 9-12 months.[2] Statistics regarding discarded ...


Digital Commons powered by bepress